Experimental Investigation of Autonomous Voltage Emergence in Passive LC Detector Systems Table of Contents Abstract 1. Introduction 2. Detector System Description 3. Measurement Methodology and Environmental Conditions 4. Detector Configuration and Measurement Methods 5. Time-Series Charging Curves and Detector Behavior 6. Detector Response During Relocation Cycles 7. Detector Dominance and Energy Distribution Shifts 8. Comparative Analysis of SMD and Traditional Detectors 9. Observed Anomalous Charge Accumulation Event 10. Discussion of Observed Physical Mechanisms 11. Conclusions and Future Directions 12. Authors and Acknowledgements Attachments References Budapest, September 2025 Ákos István Ujvári (A.I. UJVARI) – Researcher, experimental detector system developerEcho (ChatGPT) – Artificial Intelligence assistant, linguistic and scientific collaborator Based on experimental measurements with passive LC detector systems (June–August 2025) Experimental Investigation of Autonomous Voltage Emergence in Passive LC Detector Systems Abstract This study presents the experimental investigation of autonomous voltage emergence in passive LC detector systems operating under ambient environmental conditions without external power input. The detector units consist of high-inductance coils, precision capacitors, and diode-based voltage multiplication stages configured as passive resonant structures. Over an extended observation period, measurable voltage levels consistently developed across multiple detector units following controlled discharge events. The voltage accumulation exhibited characteristic temporal patterns, including gradual rise phases, detector-specific dominance shifts, and reproducible recharge behavior after discharge cycles. The experimental setup was designed to minimize external interference, with systems powered exclusively by isolated battery sources and deployed in environments free from active electronic equipment. Measurement data were recorded manually and through automated logging systems, including voltage, temperature, humidity, and timing information. The results demonstrate persistent and repeatable voltage formation in passive LC detector systems under ambient conditions. The observed behavior suggests the presence of energy coupling mechanisms between the detector structures and their surrounding electromagnetic environment. The findings provide a documented experimental basis for further investigation into passive resonant energy interactions and their potential underlying physical mechanisms. All measurement data, system configurations, and experimental conditions are provided to support independent verification and further research. Experimental Investigation of Autonomous Voltage Emergence in Passive LC Detector Systems Authors: Ákos István Ujvári (A.I. UJVARI)Independent Researcher, Experimental Detector System DeveloperBudapest, Hungary Echo (ChatGPT)Artificial Intelligence Assistant, Scientific and Linguistic Collaboration Date: September 2025Location: Budapest, Hungary Based on experimental measurements conducted between June and August 2025 using passive LC detector systems under controlled environmental conditions. 1. Introduction Passive resonant LC circuits are widely used in electronic systems for frequency selection, signal detection, and energy storage applications. Under typical operating conditions, such systems require either external excitation or coupling to ambient electromagnetic sources to produce measurable electrical responses. In high-impedance passive detector configurations, even weak electromagnetic interactions with the surrounding environment may lead to measurable voltage accumulation over extended time periods. These effects are of interest in fields such as passive sensing, electromagnetic environment monitoring, and ultra-low-energy detection systems. The present study investigates the long-term voltage behavior of passive LC detector systems constructed using high-inductance coils, precision capacitors, and diode-based voltage multiplication stages. The detectors operate without external power input and are periodically discharged to observe subsequent voltage redevelopment under ambient environmental conditions. The objective of this work is to document and characterize the observed voltage accumulation phenomena using controlled experimental conditions, systematic measurement procedures, and long-term monitoring. The study focuses on measurable electrical behavior, reproducibility, temporal characteristics, and system-level interactions between multiple detector units. This document presents the results of an experimental series conducted between June and August 2025 using passively tuned LC-based detector units operating under controlled environmental conditions. The system was designed to enable observation of voltage accumulation behavior in a network of high-impedance resonant circuits without intentional external excitation. Throughout the measurement period, the detector units consistently developed measurable voltages following discharge events. The voltage accumulation exhibited structured temporal characteristics, including repeatable charging curves, detector-specific variations, and shifts in relative voltage levels between detector units over time. Changes in detector configuration, including repositioning and system modifications, were followed by observable adjustments in voltage accumulation patterns. These observations suggest the presence of dynamic electromagnetic coupling between the detector systems and their surrounding electromagnetic environment. The purpose of this document is to provide a detailed experimental record of these observations, including system configuration, measurement procedures, and recorded data. The results are presented to support further investigation and independent analysis of passive voltage accumulation phenomena in resonant LC detector systems. 2. Detector System Description The experimental setup utilized a detector system based on the classic Greinacher voltage multiplier architecture, which has been adapted for passive resonance detection. These detectors do not require any external power source. They rely entirely on the interaction between inductance (L), capacitance (C), and the surrounding space to develop measurable voltages at their terminals. Each detector is constructed with a resonant LC circuit, where the inductor (coil) and the capacitors are carefully matched. The system's behavior is influenced by its orientation, spatial arrangement, and the properties of the surrounding environment. Detector positions are labeled D1, D2, D3, and D4 in the measurements, and each has unique characteristics (e.g., inductance values, capacitor arrangements) that contribute to the overall dynamics of the field interaction. The detectors are equipped with long wire antennas, typically 1.5 meters or longer, which extend their sensitivity to ambient spatial energy. The passive charge collection and voltage buildup across the circuit's output terminals are tracked over time, offering insights into how different spatial positions and configurations affect energy dynamics. A key element of the design is the periodic short-circuit discharge of the detectors typically every morning to reset the system and observe its natural recharge behavior. These cycles help identify the dominance shifts, communication patterns, and field responsiveness. 3. Measurement Methodology and Environmental Conditions Figure 1. Schematic diagram of the LC-based detector used for D1–D4, and system sample. The only variable elements are the input capacitance (C1, C2), tuning inductance (L), and antenna length. Measurements were performed manually, at intervals ranging from 2 to 12 hours. Measurement times were selected based on a combination of human and environmental rhythms, with the aim of observing the system's charging dynamics over both short and long periods. Voltage values were recorded in volts using a precision voltmeter, and each entry was logged with the corresponding timestamp and environmental conditions. Environmental factors such as temperature and weather (e.g., sunny, cloudy, rainy) were recorded during each measurement. While the system was located indoors, these factors were found to correlate with changes in the measured voltage values over time, suggesting possible interactions with external energy conditions. During the testing period, the detectors were periodically discharged by short-circuiting the capacitor terminals for 4 seconds. This deliberate discharge was typically performed in the early morning to observe the recharging process from a known zero state. The voltage increase after discharge, often rapid and substantial, served as a key indicator of the ambient field's energy density and its interaction with the detector configuration. Each detector was placed at a fixed location and maintained consistent component values unless a specific reconfiguration was documented. The D4 detector, introduced later in the series, followed a consistent measurement routine but was often repositioned near D1, D2, or D3 to study interaction effects. All measurement data were compiled into a structured spreadsheet, with dedicated columns for timestamp, temperature, weather, voltage values for D1–D4, and a notes section for recording specific events, such as detector repositioning, antenna length modifications, or component replacements. 4. Detector Configuration and Measurement Methods The spatial detector system was implemented using four individual detectors (D1, D2, D3, D4), all based on the same Greinacher voltage multiplier circuit design. Each detector comprises an LC circuit where the inductance and capacitance values were precisely measured and configured using a QuadTech 1715 LCR meter. This ensures that the
Ujvari et al. (Wed,) studied this question.