A 4A 12-to-1 Flying Capacitor Cross-Connected DC-DC Converter with Inserted D>0.5 Control Achieving >2x Transient Inductor Current Slew Rate and 0.73× Theoretical Minimum Output Undershoot of DSD

Automotive and industrial applications require a high-efficiency DC-DC converter to directly convert power from the 12V intermediate bus to a low-voltage point-of-load (PoL). The double step-down (DSD) buck converter [1]–[4] (shown in Fig. 18.3.1) is suitable for such applications, where a flying capacitor <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">CF</tex> sustains a half-input-voltage <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">(VIN/2)</tex> stress. Therefore, all the power switches only experience <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">VIN/2</tex> stress except <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">MA2</tex> , allowing for exploiting the benefits of low-voltage devices. Two pulse-width modulation (PWM) signals <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">φ₁</tex> and <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">φ₂</tex> with an equal duty cycle <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">D</tex> drive the DSD. A <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">PoL</tex> supply should have a small output capacitor <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">C₀</tex> if a fast dynamic voltage scaling (DVS) is needed. However, a small <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">C₀</tex> in the conventional DSD may cause a large output undershoot <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">VUS</tex> during a transient event. This comes from the low inductor current slew rate <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">I_L₋SR=(VIN/2-2V₀)/L</tex> , due to the amplitude of the inductor switching nodes <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">VXA1</tex> and <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">VXB1</tex> being reduced to <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">VIN/2</tex> by <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">CF</tex> , and the non-overlapping <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">φ₁</tex> and <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">φ₂</tex> in a conventional <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">D≤ 0.5</tex> control. Furthermore, the <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">D</tex> should cover a wide range to respond to an integral transient error in the control loop compensator. With <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">D≤ 0.5</tex> , the DSD converter may fail to cancel the error in time, and the accumulation and release of the error result in overshoot/ringing. This would be more severe at a higher output voltage <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">V₀</tex> because the steady-state <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">D</tex> is closer to 0.5. A possible solution can be to have a DSD converter that works with <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$D>0.5$</tex> . Nevertheless, this leads to an over-sterss on <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">MA1</tex> , and imbalance in inductor currents <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">ILA</tex> and <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">ILB</tex> , which should be eliminated [3].