Answers are grounded in this paper and cite their sources.
Evaluates coercivity in MnAl-C systems with soft magnetic inclusions, suggesting modifications for enhanced performance.
In this work we quantify coercivity in single and multigrain systems of MnAl-C with embedded paramagnetic and soft magnetic inclusions. Soft magnetic inclusions with a diameter greater than 10 nm, where curling and multidomain reversal is triggered by adjacent hardmagnetic entities, led to only a fraction of the coercive field achieved without the inclusions. Large misorientation angles between the external field and the easy axes of participating structural units also led to low coercivity. This was frequently observed in triple junctions formed by twin boundaries, which is one of the reasons for the poor magnetic properties in as-transformed MnAl-C. After hot-extrusion, triple junctions formed by grain boundaries are dominant and the grains have an easy-axis texture parallel to the extrusion direction. Thus, large misorientation angles are minimized and coercivity is enhanced. In the following Dataset you will find the necessary data to reproduce the plots and figures of the publication https://doi.org/10.1016/j.jmmm.2024.172390. Below follow a more detailed list what you will find including the Figure captions: Fig. 2. Inclusion models of (a) single grain, (b) twin boundary and (c) triple junction. Inclusions are either spheres or regular tetrahedrons, paramagnetic or soft magnetic, with diameters ranging from 10 nm to 150 nm. Tetrahedrons have equivalent volume than the spheres and its center of mass lies exactly in the midpoint of the model. Tetrahedrons at twin boundaries (b) are slightly rotated to avoid numerical instabilities during meshing and simulation. The models contain 1, 2 and 4 entities with different easy axis orientation for (a), (b) and (c) respectively. Triple junctions are created with three lower entities and an additional upper half sphere. - To create the finite element meshes we uploaded the Salome scripts (https://www.salome-platform.org/, last visited 2026-06-16). Fig. 6. On the left: Coercive field μ0 Hc as function of inclusion size for a single grain. On the right: Nucleation starts from the center of the soft magnetic inclusions, which is shown for both 150 nm inclusion geometries. On the bottom right: Stoner–Wohlfarth switching field μ0 HSW as function of misorientation angle φ between the external field and the easy axis of a single domain ferromagnet [16] with material properties of MnAl-C (Table 1). Fig. 7. Coercive field μ0 Hc as function of inclusion size for pseudo, true and order twin configurations. The blue curves refer to the samples with paramagnetic inclusions. The red curves refer to samples with soft magnetic inclusions. Twin angle ψ between the two easy axes, ψ = 48° , ψ = 75.66° and ψ = 95.35° for pseudo [2], true and order twin [4], respectively. Fig. 8. Demagnetization curves with soft magnetic inclusions for pseudo, true and order twin boundaries with an external field aligned and rotated by 15° into the right hemisphere. Twin models are stacked horizontally and different alignments of the external field vertically. Fig. 10. On the left: Coercive field μ0 Hc as function of inclusion size for an order twin with an external field Hext applied in z and y direction. In the center: Tetrahedral inclusions pointing in out-of-image z and y direction with corresponding easy axes configurations. On the right: Demagnetization curves of the soft magnetic inclusions. Fig. 11. On the left: Coercive field μ0 Hc as function of inclusion size for triple junctions A to D of Fig. 5. Easy axis configurations without inclusion are shown as inlay with out-of-image z-direction. The capping half sphere easy axis is aligned with the external field in z-direction. On the right: Demagnetization curves for triple junction C with soft magnetic inclusions. Early nucleation of the entity with φ → 90° and the 150 nm spherical soft magnetic inclusion is shown for C prior the first irreversible step. Fig. 12. Coercive field μ0 Hc as function of inclusion size for triple junctions formed by grain boundaries. The easy axis of the upper half sphere is aligned with the external field applied in z-direction. On the top right a schematic of the easy axis configuration is depicted with the misorientation angles φ = 45° , 45° , 45° between the external field and the easy axes. On the x–y plane the easy axes are equally distributed around 360°.
No takes yet. Share an insight, caveat, or question.
Gusenbauer et al. (2024) studied this question.
Synapse has enriched 8 closely related papers on similar clinical questions. Consider them for comparative context: