Answers are grounded in this paper and cite their sources.
As microelectronics characterization moves toward higher complexity and smaller features, specimen preparation increasingly determines practical throughput in microscopy workflows. Transmission electron microscopy (TEM) and X-ray nano-computed tomography (nanoCT) impose different but equally strict specimen constraints: TEM demands thin, low-damage lamellae with controlled geometry, while nanoCT requires free-standing microstructures with dimensions and clearances compatible with rotation and reconstruction fidelity. Focused ion beam (FIB) methods can generate high-quality final specimens, but full-depth shaping by serial ion removal is slow when many sites, larger starting volumes, or repeated studies are required. A scalable preparation strategy must therefore preserve quality while reducing dependence on ion-beam bulk removal. We describe a laser-first preparation architecture for both TEM and nanoCT, enabled by Tescan FemtoChisel platform, that reassigns bulk shaping to ultrafast-laser micromachining and reserves ion-beam processing for targeted end-stage refinement. The central principle is geometry-first preparation: create repeatable near-net-shape precursor structures rapidly, then perform minimal local thinning/polishing only where microscopy requirements demand it. For TEM preparation, paired laser trenches are used to form bridge-style precursor geometries with thickness primarily set by trench spacing. This geometry-driven method supports predictable precursor formation across multiple sites, which is advantageous for comparative studies and failure localization campaigns. By producing arrays of precursor bridges in a short time, the workflow enables high sampling density without unaffordable increases in FIB runtime. After laser shaping, limited ion-beam thinning is applied to reach electron transparency and final local finish. For nanoCT preparation, laser machining is used to generate micropillars with controllable top diameter, height, and surrounding clearance geometry. Because handling and mounting can become yield-limiting at smaller dimensions, stepped pillar architectures are employed to decouple mechanical robustness from imaging geometry. A larger lower stage improves manipulation and mounting stability, while an upper stage is dimensioned for tomography constraints. This staged geometry improves practical specimen survivability during transfer and setup while preserving imaging suitability. Across both workflows, in-process quality controls are integrated to improve microscopy-readiness. Intelligent multi-gas processing reduces redeposition accumulation and helps maintain surface cleanliness in and around prepared regions. A removable laser protective layer (LPL) improves near-edge condition and reduces unintended disturbance at imaging-critical boundaries. These controls are important because residual debris or boundary irregularity can degrade downstream imaging quality and increase rework burden during final polishing. Correlative quality assessment is performed with optical microscopy for overview and targeting, confocal topography for three-dimensional geometry verification, and SEM for local surface/edge condition. In TEM precursor routes, these measurements confirm repeatable bridge geometry and trench uniformity before focused ion beam (FIB) thinning. In nanoCT routes, they verify pillar dimensional stability and sidewall condition before tomography acquisition. The combined checks provide an objective handoff criterion: specimens enter high-cost or high-time imaging modalities only after meeting geometric and surface-quality thresholds. The practical impact is a substantial shift in where preparation time is spent. Rather than consuming most effort in serial ion-beam volume removal, the approach front-loads rapid laser shaping and uses focused final refinement where it has maximal value. This improves throughput, expands feasible site counts, and supports broader comparative studies while maintaining compatibility with high-resolution microscopy requirements. From a correlative microscopy perspective, the workflow also improves consistency. Standardized precursor geometries reduce operator-dependent variability and simplify interpretation across multiple specimens. For investigations in heterogeneous microelectronics, where both local nanoscale features and larger contextual relationships matter, this reproducibility is especially valuable. In summary, laser-first TEM and nanoCT specimen preparation provides a scalable, microscopy-centered alternative to fully serial ion-beam workflows. By combining rapid geometry formation, integrated artifact control, and targeted final refinement, the method improves preparation efficiency without sacrificing imaging readiness for advanced microelectronics characterization [16]. Batch production of bridge-type TEM lamella preforms on silicon. Top: SEM overview of a wafer-scale 2D bridge array. Middle: SEM magnified view of a representative bridge. Bottom: confocal magnified view verifying bridge geometry and thickness control. Representative trench dimensions are 50 µm × 50 µm at ∼100 µm depth, leaving an approximately 3 µm bridge; processing time is ∼30 s per site and <7 min for 12 sites. Heat-affected-zone assessment of a laser-formed bridge preform: FIB cross-section of an approximately 3 µm bridge showing minimal preparation-induced modification in the bridge body and adjacent trench-wall region. SEM images of laser-prepared nanoCT pillars at multiple target dimensions, demonstrating reproducible control of pillar geometry across a broad specimen-size range Stepped (“wedding-cake”) nanoCT pillar architecture for improved extraction and handling: the larger base supports gripping and mounting, while the smaller upper stage defines the imaging region. The surrounding extracted-area walls appear clean with no obvious visible damage.
No takes yet. Share an insight, caveat, or question.
May et al. (2026) studied this question.
Synapse has enriched 10 related papers. Consider them for comparative context: