Microstructure-based constitutive model of coronary artery with active smooth muscle contraction

Figures

• 

  Figure 1. Model predictions with integration of previously measured microstructural distributions. Solid lines denote model predictions of passive responses, and dashed lines denote predictions of full responses of coronary arteries with K+ induced SMC contraction. Symbols indicate experiment measurements and error bars denote standard deviation. (a) and (b) show the pressure-radius relationships at two axial stretch ratios of λ z = 1.3 and 1.5, respectively, and (c) and (d) show corresponding pressure-force relationships.

• 

  Figure 2. Refined geometric distributions for each sample by parameter optimization. Solid lines denote statistical distribution of previous measurement; dashed lines are distributions for samples #1, #2, #3, #4, #5, respectively. PDF denotes probability density function of a geometrical parameter.

• 

  Figure 3. Model predictions with refined microstructural distributions showing better agreements with experimental data. Solid lines denote model predictions of passive responses, and dashed lines denote predictions of full responses of coronary arteries with K+ induced SMC contraction. Symbols indicate experiment measurements. (a) and (b) show the pressure-radius relationships at two axial stretch ratios of λ z = 1.3 and 1.5, respectively, and (c) and (d) show corresponding pressure-force relationships.

• 

  Figure 4. Model predictions of transmural stress distributions at two different circumferential stretch ratios. (a–c) Full and passive stress components \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma }_{rr}$$\end{document}σrr, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma }_{rr}$$\end{document}σrr and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma }_{zz}$$\end{document}σzz vary among the vessel wall at a lower circumferential stretch ratio λ θ = 1.24 with two axial stretch ratios of λ z = 1.3 and 1.5; (d–f) the stress components vary among the vessel wall at a higher circumferential ratio \documentclass[12pt]{minimal}…

• 

  Figure 5. Model predicted stress-strain relation of middle wall of coronary arteries. (a–c) Full, passive and active stresses of middle wall vary with increase of circumferential strain at a fixed axial stretch ratio of λ z = 1.3; (d–f). Full, passive and active stresses of middle wall vary with increase of circumferential strain at λ z = 1.5.

• 

  Figure 6. The stress-strain curves of individual fibers and SMC of all samples. Comparisons were made between the full microstructure model and the mean-value approach. Solid lines denote the stresses of fibers and cells predicted by the full model, and dashed lines are predictions of mean-value approach.

• 

  Figure 7. Top: A schematic diagram of vessel configurations and geometrical parameters. The left panel is the coordinate system of vessels with three principal directions: circumferential direction θ, radial direction r and axial direction z; ZSS is zero-stress state of vessel, and loaded state means vessel under pressure P. Deformation gradient tensor F describes tissue deformation from ZSS to loaded configuration. Parameters \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({R}_{o},{R}_{i}$$\end{document}(Ro,Ri) are the outer and inner radii of stress-free vessel and R is radius to a point measured at ZSS, while θ is opening angle of vessel at ZSS. Parameters \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({r}_{o},{r}_{i}$$\end{document}(ro,ri) are the outer and inner radii of loaded vessel and r is radius to the point measured at…