Answers are grounded in this paper and cite their sources.
Protocol demonstrates selective isolation of Aspergillus terreus from environmental samples, implying improved detection methods.
Soil Extraction Plating for the Detection of Aspergillus terreus from Environmental SamplesAuthors and AffiliationsJan Schobert¹, Paul Illmer², Roya Vahedi-Shahandashti¹*, Cornelia Lass-Flörl¹*¹ ISHAM Working Group of Aspergillus terreus, ECMM Excellence Center of Mycology, Institute of Hygiene and Medical Microbiology, Medical University of Innsbruck, Austria² Institute of Microbiology, University of Innsbruck, AustriaAbstractThis protocol describes a selective soil extraction plating method for the detection and isolation of Aspergillus terreus from environmental soil samples. Sieved soil is suspended in a saline–surfactant spore buffer (0.9% NaCl, 0.1% Tween 20) to release fungal propagules, followed by plating of the supernatant onto Sabouraud agar supplemented with chloramphenicol, with or without amphotericin B. Differential incubation at 37 °C and 50 °C enhances selectivity for thermotolerant A. terreus. Suspected colonies are subcultured on oatmeal agar and identified by microscopy and sequencing.BackgroundAspergillus terreus is a clinically relevant filamentous fungus and an important environmental mold with intrinsic reduced susceptibility to amphotericin B. Soil is considered one of its main ecological reservoirs. Recovery of A. terreus from environmental samples is complicated by the heterogeneous distribution of fungal propagules and by the presence of abundant competing microorganisms.The present protocol is based on soil extraction plating and selective cultivation. Soil particles are first homogenized and fungal propagules are released into suspension using a saline-Tween buffer. After a short sedimentation step, aliquots of the supernatant are inoculated onto selective media. Chloramphenicol suppresses bacterial growth, amphotericin B provides additional selectivity, and incubation at 50 °C exploits the thermotolerance of A. terreus. Colonies suspected to represent A. terreus are purified on oatmeal agar and further identified by morphology and sequencing. Materials and ReagentsTable 1. Sabouraud Agar Composition (per 1 L)IngredientAmountUnitSabouraud 2% Dextrose Bouillon30gAgar20gDeionized water1000mLChloramphenicol (final concentration)50mg/LAmphotericin B (final concentration)50mg/LTable 2. Oatmeal Agar Composition (per 500 mL)IngredientAmountUnitOatmeal15gAgar7.5gDeionized water500mLMedia PreparationSabouraud Agar (SAB)30 g Sabouraud 2% dextrose bouillon and 20 g agar are dissolved in 1000 mL deionized water in a Schott bottle. The medium is autoclaved and cooled to approximately 45 °C before supplementation (Table 1).Chloramphenicol Stock SolutionPrepare a stock solution by dissolving 0.5 g chloramphenicol in 10 mL ethanol (50 mg/mL). Add 1 mL of this stock per 1 L medium to obtain a final concentration of 50 mg/L.Amphotericin B SupplementationUsing a stock solution of 3200 mg/L amphotericin B, add 156.5 µL per 1 L of medium already containing chloramphenicol to achieve the desired final concentration.Plate PouringPour approximately 20 mL of medium per Petri dish under sterile conditions.Oatmeal AgarGrind 15 g oatmeal using a mortar and pestle. Add to 7.5 g agar in a flask and mix with 500 mL deionized water. Autoclave, cool to ~45 °C, and pour into Petri dishes (~20 mL per plate) (Table 2).Procedure1. Soil SamplingUsing a disinfected shovel, collect approximately 10 g of soil from the top 5–10 cm and transfer into a sterile 50 mL Falcon tube.2. SievingRemove plant material, stones, and debris by passing soil through a sterile 2 mm mesh sieve.3. SubsamplingWeigh two independent 2 g portions of soil into sterile 15 mL Falcon tubes.4. Spore ExtractionAdd 5 mL of sterile spore buffer (0.9% NaCl + 0.1% Tween 20) to each tube. Perform all steps under aseptic conditions.5. HomogenizationVortex samples for 1 minute to release fungal propagules.6. SedimentationAllow tubes to stand for 1 minute to sediment larger particles.7. PlatingPlate 100 µL of the supernatant from each replicate onto:3 × SAB + CAP plates1 × SAB + CAP + AmB plateTotal: 4 plates per replicate.8. IncubationIncubate plates for 48–72 hours:All plates at 37 °COne SAB + CAP plate at 50 °C9. ScreeningExamine plates macroscopically for colonies consistent with Aspergillus terreus.10. Subculture and IdentificationTransfer suspected colonies onto oatmeal agar. Confirm identity by:Morphology (macro- and microscopic)Molecular methods (sequencing)NotesReplicate subsampling improves detection due to heterogeneous distribution in soil.The Tween-containing buffer enhances spore release.Short sedimentation reduces debris carryover.Chloramphenicol suppresses bacterial growth.Amphotericin B increases selectivity.Incubation at 50 °C is critical for selecting thermotolerant A. terreus.ApplicationsEnvironmental detection of Aspergillus terreusIsolation of environmental strainsEpidemiological and ecological studiesDownstream susceptibility testing and sequencingAcknowledgmentsAdapted from: Schobert J., Illmer P., Vahedi-Shahandashti R., Lass-Flörl C.Conflict of InterestThe authors declare no conflict of interest.
No takes yet. Share an insight, caveat, or question.
Schobert et al. (2026) studied this question.
Synapse has enriched 10 related papers. Consider them for comparative context: