Synapse

← Technology of metals

Papers in Technology of metals

Page 4 · newest first

  1. Composition evolution of ion-doped layer of titanium alloy b6 after aluminum ion irradiationTechnology of metals · 2023
  2. Experimental study of drawing process of pipes with variable wall thicknessTechnology of metals · 2023
  3. Combined extraction of anisotropic relaxing materialTechnology of metals · 2023
  4. Determination of temperature in contact zone during pendulum surface plastic deformation of structural steelTechnology of metals · 2023
  5. Some cases of biocorrosion of supports in underground mine workings of various climatic zonesTechnology of metals · 2023
  6. Investigation of effectiveness of alternative silicon-containing material for cast iron smeltingTechnology of metals · 2023
  7. Achievement of rational balance of resistance of nitrided austenitic chromium-nickel steel to wear and corrosionTechnology of metals · 2023
  8. Extrusion of solid stepped products with cylindrical section passing into section of square cross-section. Problem statement. Part 1Technology of metals · 2023
  9. Determination of values of contact pressure and depth of penetration of fretting particle into half-space of bearing interface and implementation of resultsTechnology of metals · 2023
  10. Use of monte carlo method in determination of size of lamellae in decomposed solid solutions (w, cr)Technology of metals · 2023
  11. Investigation of effect of various deoxidizers on structure and properties of low-carbon steelsTechnology of metals · 2023
  12. Forecast of residual life of "lemken" plough bits and dimensional groups of parts suitable for operationTechnology of metals · 2023
  13. Effect of citrate solution composition on process of autocatalytic deposition of nickel-phosphorus-tungsten alloyTechnology of metals · 2023
  14. Development of automation methods for design of layouts of universally assembled machine toolsTechnology of metals · 2023
  15. Optimization of heat treatment modes for 20gml steel billets operating at temperatures up to minus 40 °cTechnology of metals · 2023
  16. Determination of residual stresses, using barkhausen noise when hardening of parts with pendulum toolTechnology of metals · 2023
  17. Investigation of structural and physical-mechanical properties of reaction-sintered ceramics based on silicon carbideTechnology of metals · 2023
  18. Solution of some automation problems for control of casting machineTechnology of metals · 2023
  19. Extrusion of solid stepped products with cylindrical section passing into section of square cross-section. Experimental check of obtained theoretical results. Part 4Technology of metals · 2023
  20. Effect of filtration refining on microstructure and mechanical properties of vzh-159 alloyTechnology of metals · 2023
  21. Investigation of effect of functional gas-thermal coatings on fatigue strength of structural materialsTechnology of metals · 2023
  22. Development of technology for directed crystallization of castings from heat-resistant and intermetallic alloys (review)Technology of metals · 2023
  23. Theoretical study of contact pressure reduction during cold rolling of strips with transition to single-zone backward-slip processTechnology of metals · 2023
  24. Influence of cast core sizes on properties of point joints of aluminum alloysTechnology of metals · 2023
  25. Features of structure formation of silicide-oxide resistive alloys during pulsed pressingTechnology of metals · 2023
  26. Influence of scale factor on modulus of elasticity determined by instrumental indentationTechnology of metals · 2023
  27. Extrusion of solid stepped products with cylindrical section passing into section of square cross-section. Determination of kinematic and stress states. Part 2Technology of metals · 2023
  28. Hardening technologies of flat knives by hfc-borationTechnology of metals · 2023
  29. Assessment of operability and durability of restored parts and jointsTechnology of metals · 2023
  30. Influence of milling modes and negative temperature on strength of carbon-filled plastics under cyclic bending loadingTechnology of metals · 2023
  31. Evaluation and selection of working gases for plasma coating methods on stationary and mobile plantsTechnology of metals · 2023
  32. Production of connecting parts of oil-and-gas pipeline systems of increased strength and corrosion resistance, made of welded billetTechnology of metals · 2023
  33. Ways to reduce electricity consumption during production of aluminumTechnology of metals · 2023
  34. Scratch-testing of surface layers of materials and coatings, using acoustic emissionTechnology of metals · 2023
  35. Optimization of heat treatment of magnetic hard powder alloy fe-30cr-16co-1smTechnology of metals · 2023
  36. Determination of waviness of cylindrical parts during pendulum surface plastic deformationTechnology of metals · 2023
  37. Heat resistance of transition metals with an aluminized coatingTechnology of metals · 2023
  38. Improvement of technology for production of fine-dispersed materialTechnology of metals · 2023
  39. Process investigation of structure formation of steel 09g2c produced by method of additive electric arc growthTechnology of metals · 2023
  40. Effect of microstructure of heat-resistant nickel alloys on rate of fatigue crack growthTechnology of metals · 2023
  41. Influence investigation of parameters of modification of cast iron on crystallization parameters, using thermal analysisTechnology of metals · 2023
  42. Experimental plant and methodology for study of formation and change in structure of metal solidifying under thermomechanical influence conditionsTechnology of metals · 2023